Please use this identifier to cite or link to this item:https://hdl.handle.net/20.500.12259/91336
Type of publication: conference paper
Type of publication (PDB): Tezės kituose recenzuojamuose leidiniuose / Theses in other peer-reviewed publications (T1e)
Field of Science: Mechanikos inžinerija / Mechanical Engineering (T009)
Author(s): Steponavičius, Dainius;Kemzūraitė, Aurelija;Kiniulis, Valdas;Andriušis, Albinas;Juknevičius, Darius
Title: Influence of Cylinder Design on its Speed During Corn Ear Threshing
Is part of: Rural Development 2017 [elektroninis išteklius]: Bioeconomy Challenges : The 8th International Scientific Conference, 23-24th November, 2017, Aleksandras Stulginskis University : Abstracts Book. Akademija : Aleksandras Stulginskis University, 2017
Extent: p. 150-151
Date: 2017
Note: Puslapiai nurodyti pagal pataisytą leidinį
Keywords: Concave;corn ear;feed rate;threshing cylinder
ISBN: 9786094491238
Abstract: Technological and structural parameters of a threshing unit must ensure the highest possible quality of its operation under minimum input and cost. The aim of the study was to estimate the variation of speed of threshing cylinder with two different shapes of filler plates (FP-I and FP-II) under various corn ear feed rate into combine harvester. Threshing cylinder speed (frequency of rotation) nb (min-1) was measured simultaneously each 0.075 s using stationary tangential single-cylinder threshing unit located in laboratory-training ground intended for investigation into technological processes of agricultural machinery. Frequency of rotation of non-loaded threshing cylinder speed amounted for 450 min-1. Increase in corn ear feed rate from 6 kg s-1 to 12 kg s-1 caused frequency of rotation of threshing cylinder to decrease from nb=437.82±0.21 min-1 to nb=420.96±0.50 min-1 (using FP-I). Replacing covered spaces between rasp bars with FP-II had no effect on cylinder speed – it has decreased from 438.06±0.23 min-1 to 421.37±0.32 min-1.Results showed that in case of FP-I, the amplitude of speed Anb has increased from Anb=4.07±0.44 min-1 to Anb=8.60±0.88 min-1, whereas in case of FP-II – from Anb=2.67±0.25 min-1 to Anb=4.52±0.62 min-1 in response to increased feed rate from 4 kg s-1 to 12 kg s-1. This means that using the covers FP-II the threshing apparatus will work more evenly. The average threshing cylinder speed, irrespective of the closure of spaces between rasp bars, was found to decrease by approx. 20 min-1 in result of increase in corn ear feed rate from 4 kg s-1 to 12 kg s-1. When threshing corn ears, irrespective of the shape of filler plates, the acceptable feed rate amounted for 10 kg s-1, as it caused to exceed the permissible limit of 5% allowed for decrease in cylinder speed (nb=427.5 min-1)
Internet: http://www.ruraldevelopment.lt/doc/SANTRAUKOS_%20GERAS.pdf
Affiliation(s): Vytauto Didžiojo universitetas
Žemės ūkio akademija
Appears in Collections:Universiteto mokslo publikacijos / University Research Publications

Show full item record
Export via OAI-PMH Interface in XML Formats
Export to Other Non-XML Formats


CORE Recommender

Page view(s)

30
checked on Jun 6, 2021

Download(s)

6
checked on Jun 6, 2021

Google ScholarTM

Check

Altmetric


Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.